Vatrer Lithium Battery: How to Connect Bluetooth

Vatrer Lithium Battery APP Guide: How to Connect Bluetooth

Table of Contents

    Bluetooth Connection Guide

    Step 1: Scan the QR code of the Bluetooth APP below (Figure 1.1) to identify the QR code;(Left picture for IOS client, right picture for Android client) or open your mobile browser, search ”xiaoxiang” and download the app (Figure 1.2).

    App download QRCode

    (Figure 1.1)

    xiaoxiang APP

    (Figure 1.2)

    Step 2: After the Bluetooth APP is successfully installed, open the APP. After allowing the Bluetooth to be opened and obtaining the location information, the APP will automatically pop up the account registration page as shown in Figure 1.3. Please enter the mobile phone number as required, set the password, and confirm the completion point (Figure 1.4).

    If you forget the login password, you can use the email box to reset the password:

    1). Open the login interface, find the forgotten password, and click it to pop up the reset password interface;

    2). Enter the bound email address and click Send verification code. Generally, the verification code will be received within 60 seconds, please open the email box to check;

    3). Enter the verification code, set a new password, and click “confirm”. Figure 1.5

    sign up

    Figure 1.3

    sign in

    Figure 1.4

    forgot password

    Figure 1.5

     

    Step 3:

    l). Connect Bluetooth: After successful login, the APP will jump to the Bluetooth list, select the Bluetooth to connect.

    2). Switch the battery: when there are multiple batteries, you can select multiple Bluetooth names in the list, and quickly switch the battery that needs to be connected in the real-time interface.

    3). Scanning code connection: in the upper right corner of the real-time interface, click the scanning code button, you can directly connect by scanning the Bluetooth module bar code.

    4). Search Bluetooth: device list page, when there are multiple batteries, you can search for the Bluetooth name, quickly find the battery that needs to be connected.

    5). Disconnect Bluetooth: device list page, click disconnect. (Figure 1.6) (Figure 1.7).

    device list

    Figure 1.6

    information

    Figure 1.7

    Status Display

    1. Capacity information: At static, only the SOC percentage and remaining capacity of the battery are displayed. Display estimated full time when charging; The estimated discharge time is displayed during discharge. (Figure 1.8).

    2. Switch and protection status: The current status of the charge and discharge switch is 0n. "ON" is displayed when the switch is on, and "OFF"is displayed when the switch is on. If the balance is enabled, "ON" is displayed. If the balance is not enabled, "OFF" is displayed. Protection status: When the protection board triggers the protection threshold or manually controls charge and discharge, the corresponding protection status is displayed, If the protection status is not triggered,"OFF" is displayed.

    3. Battery information: Read or calculate through the protection board, and the following data is displayed on the APP: total voltage, current, power, maximum single voltage, minimum single voltage, average voltage, pressure difference, and cycle number.

    4. Temperature and humidity: Temperature 1 and MOS temperature are the ambient temperature of the protection board. The other is the external NTC temperature to detect the temperature of the battery cell.

    5. Single series voltage: single series cell voltage, the protection board collects cell information, the highest voltage is displayed green, the middle value is displaved blue, and the lowest voltage is displayed gray.

    status display

    Figure 1.8

    Control Button

    1. Charge and discharge switch: Through the APP can directly control the charge and discharges witch on or off, control the battery charge/discharge.

    2. Automatic balancing: Forcibly enable the balancing function. If the function is successfully enabled, the real-time balancing status is displayed on the page.

    3. Clear alarms: Clear alarm data.

    4. Reset capacity: Re-estimate the remaining capacity based on the current voltage. (Figure 1.9).

    control

    Figure 1.9

    Parameter Data

    1. Click on the History TAB. Figure 1.10

    2. Click the parameter column and then click Basic Parameter, as shown in Figure 1.11

    3. Click Initial Settings to view: nominal capacity, cycle capacity, full charge capacity, battery string number. Figure 1.12

    4. Click Basic information to view basic battery information. If necessary, you can enter the Bluetooth number in the box and click Settings to change the Bluetooth number. Figure 1.13

    history

    Figure 1.10

    parameter

    Figure 1.11

    origin setting

    Figure 1.12

    basic information

    Figure 1.13

    Device Association

    1. Bind device: When connecting Bluetooth for the first time, the APP will automatically pop up a dialog box prompting: Whether to bind this device, click “0K“ to bind; You can modify parameters only with permission from the background. Figure 1.14

    2. Unbind the device: Enter the My screen, select the device to be unbound, and click Unbind. One account can be bound to multiple devices, as shown in Figure 1.15 and Figure 1.16

    binding device

    Figure 1.14

    version info

    Figure 1.15

    unbind device

    Figure 1.16

    Hi
    I have 2 batteries in parallel, the app is displaying both batteries but it only connects to 1 !!

    Khalid Al-Wahaibi | May 03, 2025

    Hello

    I have bought 8 Vatrer 12 Volt 300Ah Self Heating Lithium Battery and made 2 string of 48 volts for my off grid solar.

    can i use the Vatrer 58.4V 20A Intelligent AC-DC 48V Golf Cart LiFePO4 Battery Charger to charge 1 string at a time…..

    I do not want to change each battery individually.

    joe croghan | Apr 07, 2025

    Hello All,
    I forgot my password to connect to the just bought and brandnew 300Ah-battery. I urgently need your help and support and ask for advice and the code the app requires.

    My Emailadress: brist.kappel@t-online.de (should be registered)
    Battery: DCJI01135J-003

    May you please help !

    Thanks a lot in advance,
    Stefan Kappel

    Stefan Kappel | Feb 25, 2025

    I need to know if the bluetooth app has the ability to present more than one battery in series and/or parallel or if I am required to connect and analyze each battery individually? This feature I am accustomed to using the app for my two 200ah Ultimatron France lifepo4’s using their respective app. Thanks!

    Nicholas | Oct 18, 2024

    Ich habe das Passwort in der App verstellt und kann meine Einstellungen nicht mehr einstellen.
    Wie lautet das Standard Passwort.
    Liebe Grüße
    Franz Berger

    Franz Berger | Oct 15, 2024

    Leave a comment

    Please note, comments need to be approved before they are published.